> ## Documentation Index
> Fetch the complete documentation index at: https://docs.visualradioassist.live/llms.txt
> Use this file to discover all available pages before exploring further.

> ## Agent Instructions
> Use the names from the glossary at https://docs.visualradioassist.live/glossary: Audio Manager (two words), command (never commando), on air and off air (never live) for programs and studios, and server apps for the VRA apps installed in the studio.
> Say which app an answer applies to, like VRA Cloud, the Core or the Output Player, and the version when the page names one.
> Only give settings, values and steps that are in these docs. Never invent one. If the docs don't cover it, say so.
> When the docs don't answer the question, send the user to Visual Radio Assist support at https://cloud.visualradioassist.live/support.

# Thresholds and calibration

> Set how loud a mic must be before its Audio Manager trigger fires: a fixed level, or a calibrated margin above the mic's own background noise.

The threshold is the line a mic has to cross before its trigger fires. Set it too low and bleed from a co-host or a monitor speaker cuts the camera. Set it too high and the presenter has to raise their voice before the camera follows. You find the threshold in the **Threshold** section of the trigger editor, next to a live meter of the input.

A new trigger starts on a fixed level. Calibrate each trigger once, so it uses a margin above that mic's own background instead.

## Calibrate a trigger

Calibration measures the mic in your studio and sets the margin for you. It needs a saved trigger with an input and no unsaved changes. Click **Calibrate** in the **Threshold** section.

**1. Stay quiet**

Make sure nobody talks into this mic. Background, bleed and room tone are
fine, they are what is being measured. Click **Start**. The measurement
takes 3 seconds.

**2. Talk normally**

Have the presenter speak into the mic at their normal presenting level.
Click **Start** and keep talking for 3 seconds.

**3. Apply**

Check the result and click **Apply**, or **Re-measure** to try again.

The result shows three numbers:

* **Floor** - The average level while the mic was quiet.
* **Talk** - A low point of the speaking level, so quiet syllables still clear the line.
* **Gap** - The difference between the two.

The **Recommended margin** is a bit under half the gap, kept between 8 and 40 dB. **Apply** saves it straight away and switches the trigger to **Above floor**.

> [!WARNING]
>
> If the gap is under 12 dB, the quiet and talk levels are too close for level
> alone to tell talk from bleed. You can apply anyway, but the trigger will
> likely fire on bleed. Wire this channel to console tally instead, or fix the
> gain staging and calibrate again.

If calibration reports **No live signal from this mic**, make sure the device is connected and the Audio Manager is online, then try again.

## Threshold modes

Each trigger has a **Threshold mode**:

* **Absolute** - A fixed **Trigger level** in dB, from -96 to +12. A new trigger starts here, at -35. Drag the line on the meter or type a value. The trigger fires when the mic is louder than this level.
* **Above floor** - A **Margin above floor** in dB, from 0 to 40. This is the mode calibration sets. The Audio Manager keeps measuring the mic's resting background, its floor, and fires when the level rises this far above it.

Below the meter, Above floor mode shows the **Live level**, the measured floor and where the trigger fires. Until a floor is measured it reads **Waiting for floor measurement. Calibrate or let the mic settle.**

Switching the mode by hand resets the value to that mode's default: -35 dB for Absolute, 12 dB for Above floor.

## Gated inputs and mic presets

When an input has **Post processing** turned off, the Audio Manager runs its own noise gate on it with a mic preset, see [Set up the Audio Manager](https://docs.visualradioassist.live/audio-manager/set-up.md#set-up-an-unprocessed-mic). The **Threshold** section then shows **Gated by mic preset**: the gate's open and close levels decide when the trigger fires, and the threshold is not used.

A gated input can't be calibrated. Click **Edit gate** to change its levels.

## Adjust thresholds from the metering view

Switch the trigger list to **Live metering** to see every trigger as a channel strip with a fader from -96 to +12 dB. Drag a fader to move that trigger's threshold. The change saves on its own, without pressing Save. The trigger that is open in the editor is the exception: its threshold is saved with **Save audio trigger**.

Faders of gated inputs read **GATED**, and faders in Above floor mode show the margin, like **+12 FLR**. Both are read-only here.

> [!WARNING]
>
> A threshold you drag in the metering view takes effect at once. Doing this
> during a show changes what goes on air immediately.

## Related

* [Audio triggers](https://docs.visualradioassist.live/audio-manager/audio-triggers.md)
* [Watch triggers on air](https://docs.visualradioassist.live/audio-manager/during-a-show.md)
* [Troubleshoot the Audio Manager](https://docs.visualradioassist.live/audio-manager/troubleshooting.md)


This documentation is built and hosted on [Mintlify](https://mintlify.com), a developer documentation platform.